Tools › Aerodynamics › Trajectories and Spaceflight › Atmospheric Entry Heating and Deceleration


Atmospheric Entry Heating and Deceleration

Enter how fast and how steeply a capsule, probe or meteoroid meets the atmosphere, with its mass, size, drag coefficient and nose radius; get its peak deceleration in g, the peak heat flux at the nose, the total heat load and where each one happens, with the deceleration and heating drawn against time. Earth, Mars, Venus and Titan. Ballistic (non-lifting) entry only; no radiative heating, ablation or breakup.

  • Peak g, peak stagnation heat flux, heat load, time above a chosen g level and the altitude and speed of each peak

  • The Allen and Eggers closed form (NACA Report 1381) beside a numerical integration with gravity and the curve of the planet, with the difference

  • Why capsules are blunt: the same entry with a second nose radius or entry angle, and with twice the mass

Atmospheric Entry Heating and Deceleration


Unit System: /

/

1. Planet and Entry (angle below horizontal)




2. Vehicle







3. Atmosphere and Heating





4. Limits and Comparison




×

Atmospheric Entry Heating and Deceleration

Allen and Eggers, Sutton and Graves, What It Assumes, Common Mistakes

What the tool does

It follows a body with no wings and no lift (a capsule, a probe, a meteoroid) from the top of an atmosphere down to the ground or to the point where the air has taken nearly all its speed. It reports the peak deceleration in g, the peak heat flux at the nose, the total heat the nose soaks up and where each one happens, first by the classic closed-form solution and then by a numerical integration that keeps gravity and the curve of the planet.

The idea

A body arriving from space carries an enormous amount of kinetic energy: at 11 km/s, about 60 MJ for every kilogram, more than ten times the energy of the same mass of TNT. All of it must go somewhere before the body reaches the ground. The atmosphere takes it through drag, a force that points straight back along the path and grows with the density of the air and with the square of the speed (Figure 1).

A blunt capsule on a path that slopes below the local horizontal by the entry angle, with drag pointing back along the path, weight pointing down and a bow shock standing ahead of the blunt nose; the air is thin above and dense below
Figure 1: A blunt body entering an atmosphere whose density grows exponentially toward the ground

The density of an atmosphere rises roughly exponentially as you go down: every step of one scale height H (about 7 km on Earth) multiplies it by e = 2.718. So the body first flies through almost nothing at full speed, then the air thickens faster than the body slows and the drag climbs steeply, and finally the body has lost so much speed that the drag falls again even though the air keeps thickening. Between the two there is a peak. In 1958 H. Julian Allen and A. J. Eggers of NACA showed that this peak can be written down in one line, and that it has a surprising property: it does not depend on the mass, the size or the shape of the body, only on how fast and how steeply it arrives.

The heating follows the same story with a different mix of density and speed, so it peaks earlier and higher up. Allen and Eggers drew the conclusion that shaped every capsule since: the heat that reaches the surface is smallest when the nose is blunt. A blunt body pushes a strong, detached shock wave ahead of itself; most of the energy goes into heating the air that streams around the body and is left behind in the wake, and only a small share reaches the wall. A sharp, slender body does the opposite.

The equations

Model. The atmosphere is ρ = ρ0 exp(−h / H), with h the altitude. The body has mass m, frontal area A = π d2 / 4 and a constant drag coefficient CD; these three enter only as the ballistic coefficient β = m / (CD A), in kg/m² (the report writes β for 1/H instead; this page uses β for the ballistic coefficient, as is usual today). The body enters at speed VE on a path γE below the local horizontal.

Closed form (NACA Report 1381). Allen and Eggers neglect gravity beside the drag and take the path as a straight line at the entry angle. The equation of motion then integrates to (their eq. 13)

V = VE exp[−B exp(−h / H)],   B = ρ0 H / (2 β sin γE)

The deceleration is −dV/dt = ρ V2 / (2 β). Setting its derivative to zero gives (eqs. 15, 16, 17)

peak deceleration = VE2 sin γE / (2 e H),   at h1 = H ln[ρ0 H / (β sin γE)],   where V1 = VE / √e = 0.61 VE

Divide by g0 = 9.80665 m/s² for the answer in g. The ballistic coefficient appears only in the altitude. If h1 comes out negative the body reaches the ground before the peak, and the largest deceleration is the one at impact (eq. 21).

Heat flux at the nose (NASA TR R-376). At the stagnation point, where the flow first meets the body, Sutton and Graves correlated boundary-layer solutions for many gases as (their eq. 33)

q √(Rn / ps) = K (hs − hw)

with q the heat flux, Rn the nose radius, ps the stagnation pressure in atmospheres, hs and hw the enthalpy of the gas at the stagnation point and at the wall, and K a constant of the gas: 0.1113 kg/(s·m1.5·atm0.5) for air, 0.1210 for carbon dioxide, 0.1112 for nitrogen (their Table II; q then comes out in MW/m² with h in MJ/kg). At entry speeds the stagnation pressure is close to ρ V2 and the enthalpy to V2 / 2, the wall being cold by comparison. With these two substitutions, which are this tool's and not printed in the report,

q = k √(ρ / Rn) V3,   k = K / (2 √101,325) = 1.748 × 10−4 for air (q in W/m² with ρ in kg/m³, Rn in m, V in m/s)

This is the form in which the relation is usually quoted (often with 1.74 × 10−4 for Earth). Allen and Eggers had the same form with a constant about half as large, and said in a footnote that real-gas effects could raise it by up to a factor of two. Putting the closed-form speed into it and maximizing gives (their eqs. 46 to 48 with the newer constant)

peak flux = k √[β sin γE / (3 e H Rn)] VE3,   at h3 = H ln[3 ρ0 H / (β sin γE)],   where V3 = VE e−1/6 = 0.85 VE

The peak heating therefore comes H ln 3 (about 8 km on Earth) above the peak deceleration.

Heat load. The flux integrated over time, per unit area of the nose. Along the closed-form path the integral can be done exactly (this tool's result; it is not printed in either report):

Q = k VE2 √[π β H / (Rn sin γE)] × [erf(√(2B)) − erf(√(2B) e−hE / 2H)]

The bracket is the share of the pulse between the entry altitude hE and the ground and is nearly always 1. Note the entry angle: a steeper entry raises the peak flux (√sin γ) but lowers the heat load (1 / √sin γ), because the pulse is shorter.

Numerical integration. The tool also integrates the full planar equations over a round, non-rotating planet of radius Rp and gravitational parameter μ, with r = Rp + h and g = μ / r2:

dV/dt = −ρ V2 / (2 β) + g sin γ
dγ/dt = (g / V − V / r) cos γ
dh/dt = −V sin γ
dQ/dt = k √(ρ / Rn) V3

by the fourth-order Runge–Kutta method with a fixed step (1/400 of the time the body needs to cross one scale height at entry, never more than 0.1 s). The second equation is what the closed form leaves out: gravity bends the path down, and the term V / r bends it up, because a body moving fast enough tends to follow the curve of the planet. At orbital speed the two cancel. The run ends at the ground or when the speed has fallen to 2 % of the entry speed. The headline numbers of the tool are the numerical ones; the closed form is shown beside them with the difference.

Planets

Gravity and radius come from the NASA planetary fact sheets (Titan: mass and radius from the Saturnian satellite fact sheet). The atmosphere numbers are:

  • Earth: ρ0 = 0.859 kg/m³, H = 7.52 km. This is a least-squares fit of this tool to the U.S. Standard Atmosphere, 1976 between 30 and 80 km, where capsules do their slowing; it stays within 14 % of the standard density there. It is not the surface density. The fact sheet's surface values (1.217 kg/m³, 8.5 km) give two to five times too much density at those altitudes. Allen and Eggers used 0.0034 slug/ft³ and 22,000 ft (1.752 kg/m³, 6.71 km), which fits 6 to 55 km and suits dense bodies that slow low down.
  • Mars: 0.016 kg/m³ and 11.0 km, the surface density and scale height of the fact sheet. K for carbon dioxide.
  • Venus: 65 kg/m³ and 15.9 km, from the fact sheet. K for carbon dioxide. Venus is much colder aloft than at the surface, so its real scale height at entry altitudes is several times smaller: with these numbers the tool puts the peaks far too high and gives a peak deceleration that is too low. Enter your own scale height in Advanced mode.
  • Titan: 5.47 kg/m³ and 33.5 km, a two-point fit through the densities at the surface and at 400 km printed in the sample output of the Titan-GRAM user guide. NASA publishes no Titan fact sheet with a scale height. K for nitrogen.

What it assumes

  • No lift. The body flies a ballistic path with a constant drag coefficient and a constant mass.
  • An exponential atmosphere at rest on a round planet that does not rotate. The entry speed is the speed relative to the air.
  • Heating by convection at the stagnation point of a blunt, axisymmetric nose, laminar flow, gas in chemical equilibrium, a wall that is cold beside the gas. Stagnation pressure ρ V2 and enthalpy V2 / 2.
  • The closed form adds: no gravity, and a straight path at the entry angle.

When it misleads

  • Shallow entries. Below about 10° at orbital speed and above, the path bends so much that the closed form can be off by a factor of two in either direction. The numerical integration shows it; trust that one.
  • Crewed capsules. Apollo, Soyuz and Orion fly with lift to hold the deceleration down. Apollo 10 entered at 36,309 ft/s and 6.6° and peaked at 6.8 g; the same entry without lift peaks at about 17 g in this tool.
  • Fast entries. Above about 10 km/s the glowing shock layer radiates heat onto the body, more so for a large nose radius. That heating is not in the model and can exceed the convective part. The correlation itself was fitted between 2.3 and 116.2 MJ/kg (about 2.1 to 15.2 km/s); the tool says when you are outside it.
  • Meteoroids. A real stone melts, sheds mass and usually breaks up under the pressure. The numbers show what an indestructible stone would face, which is the reason it does not survive.
  • Altitudes. No real atmosphere is exactly exponential. The sizes of the peaks depend on the scale height at the altitude where they happen; the altitudes also depend on the reference density. Expect altitudes good to a few kilometers on Earth and much less on the other planets with the built-in numbers.
  • Heat-shield design. The heat flux here is for a cold, non-reacting wall at one point. Ablation, surface chemistry, turbulence and the rest of the surface need other tools.

Common mistakes

  • Using the surface scale height. The peak deceleration is inversely proportional to H. The scale height that matters is the one at 40 to 70 km on Earth (about 7 to 8 km), not the 8.5 km of the surface.
  • Entering the flight-path angle with its sign, or measuring it from the vertical. Mission reports give γ = −6.5°: that is 6.5° below the horizontal. A vertical entry is 90°.
  • Expecting a heavier capsule to pull more g. In the closed form it pulls exactly the same; it only goes deeper first. What grows with the ballistic coefficient is the heating (as its square root).
  • Mixing up the two peaks. Peak heating comes first, with 85 % of the speed left; peak deceleration later and lower, with 61 % left. They are not the same instant.
  • Using the base radius as the nose radius. The nose radius is the radius of curvature at the stagnation point. A blunt capsule's heat shield is a shallow spherical cap whose radius is larger than the capsule itself; a sphere-cone probe has a nose radius well under its base radius.
  • Units in the heating formula. k = 1.748 × 10−4 goes with kg/m³, m and m/s and gives W/m². Divide by 10,000 for W/cm². With km/s the answer is wrong by a factor of 109.
  • Confusing heat flux with heat load. Flux (W/cm²) is a rate and decides the material; load (J/cm²) is the total and decides the thickness. A steep entry is worse for the first and better for the second.
  • Using inertial speed for a rotating planet. Drag and heating depend on the speed relative to the air. For Mars Pathfinder the two differed by more than 0.3 km/s.
  • Trusting the closed form for a return from orbit. At 1.5° and 7.8 km/s it gives about 4 g; the numerical answer is about 8 g, which is what the first orbital capsules saw.

How it was checked

The closed form reproduces the equations of NACA Report 1381 (eqs. 13 to 21 and 44 to 50) and its printed example, a 1-ft iron sphere falling vertically at 10,000, 20,000 and 30,000 ft/s, whose peak decelerations read from the report's Figure 3 are about 26, 105 and 235 g near 45,000 ft (the tool: 26.0, 103.9 and 233.9 g at 43,900 ft). The heating coefficients are those of Table II of NASA TR R-376. The numerical integration, the maxima of the closed form and the heat-load integral agree with an independent scipy computation on fifty entries to about one part in a million. Against flights the model is rough, as it should be: Stardust 39.5 g against 32.9 g reconstructed; Mars Pathfinder 109 W/cm² against a published 105 W/cm². One source misprint was found: NASA TN D-6725, page 14, prints an Apollo 11 entry speed of 39 194 ft/sec where its own Figures 10 and 11 give 36 200 ft/sec.




References

Allen, H. J., and Eggers, A. J., Jr. (1958). A Study of the Motion and Aerodynamic Heating of Ballistic Missiles Entering the Earth's Atmosphere at High Supersonic Speeds. NACA Report 1381, National Advisory Committee for Aeronautics, Washington, DC.

Sutton, K., and Graves, R. A., Jr. (1971). A General Stagnation-Point Convective-Heating Equation for Arbitrary Gas Mixtures. NASA Technical Report R-376, National Aeronautics and Space Administration, Washington, DC.

National Oceanic and Atmospheric Administration, National Aeronautics and Space Administration, and United States Air Force (1976). U.S. Standard Atmosphere, 1976. NOAA-S/T 76-1562, U.S. Government Printing Office, Washington, DC.

Williams, D. R. (2025). Planetary Fact Sheets: Earth, Mars, Venus and the Saturnian Satellites. NASA Space Science Data Coordinated Archive, Goddard Space Flight Center, Greenbelt, MD.

Justh, H. L., and Hoffman, J. (2020). Titan Global Reference Atmospheric Model (Titan-GRAM): User Guide. NASA Technical Memorandum 20205006805, Marshall Space Flight Center, Huntsville, AL.

Graves, C. A., and Harpold, J. C. (1972). Apollo Experience Report: Mission Planning for Apollo Entry. NASA Technical Note D-6725, National Aeronautics and Space Administration, Washington, DC.

Desai, P. N., and Qualls, G. D. (2008). "Stardust Entry Reconstruction." AIAA Paper 2008-1198, American Institute of Aeronautics and Astronautics, Reston, VA.

Desai, P. N., Lyons, D. T., Tooley, J., and Kangas, J. (2006). "Entry, Descent, and Landing Operations Analysis for the Stardust Re-Entry Capsule." AIAA Paper 2006-6410, American Institute of Aeronautics and Astronautics, Reston, VA.

Steltzner, A., Desai, P., Lee, W., and Bruno, R. (2003). "The Mars Exploration Rovers Entry Descent and Landing and the Use of Aerodynamic Decelerators." AIAA Paper 2003-2125, American Institute of Aeronautics and Astronautics, Reston, VA.

Desai, P. N., and Lee, W. J. (2005). "MER EDL: Overview and Reconstruction Status." In 2nd International Planetary Probe Workshop, NASA Ames Research Center, Moffett Field, CA.

Wright, M. J., Tang, C. Y., Edquist, K. T., Hollis, B. R., and Krasa, P. (2010). "A Review of Aerothermal Modeling for Mars Entry Missions." AIAA Paper 2010-0443, American Institute of Aeronautics and Astronautics, Reston, VA.

Striepe, S. A., Blanchard, R. C., Kirsch, M. F., and Fowler, W. T. (2007). "Huygens Titan Probe Trajectory Reconstruction Using Traditional Methods and the Program to Optimize Simulated Trajectories II." AAS Paper 07-226, American Astronautical Society, San Diego, CA.

National Aeronautics and Space Administration (1962). Results of the First United States Manned Orbital Space Flight, February 20, 1962. Manned Spacecraft Center, National Aeronautics and Space Administration, Washington, DC.


DISCLAIMER: The methods and calculation on aNOWysis.com are provided as means to educate the reader. There is no warranty, expessed or implied, as to the relevance or accuracy of the methods or calculations. All calculations should be checked by a qualified analyst for appropriateness and accuracy. We will not be held liable for any damages, injuries or deaths caused by using methods or calculations from this site.