Tools › Aerodynamics › Trajectories and Spaceflight › Ball Flight with Drag and Spin


Ball Flight with Drag and Spin

Pick a ball and enter how it is launched (speed, angle, spin, wind and the altitude of the field); get how far it carries, how high it goes, how long it flies and how fast it lands, with its path drawn against the same throw at sea level, without spin and with no air at all. Presets for a baseball, golf ball, soccer ball, tennis ball, basketball and a falling penny, or your own object.

  • Carry, peak height, time of flight, landing speed and angle, sideways curve and terminal velocity

  • The path drawn four ways: as entered, at sea level, without spin and in a vacuum, plus the launch angle that carries farthest

  • Drag and spin-lift coefficients of the baseball and the soccer ball from NASA Glenn's Beginner's Guide to Aeronautics; checked against closed forms and an independent numerical integration

Ball Flight with Drag and Spin


Unit System: /

/

Object






Launch







Field and Air (temperature in °F for USCS, °C for SI)Field and Air







×

Ball Flight with Drag and Spin

Drag, the Magnus Force, Thin Air, What It Assumes, Common Mistakes

What the tool does

It follows a ball from launch to landing with the three forces that act on it in flight: its weight, the drag of the air, and the sideways or upward push that spin gives it. It reports how far the ball carries, how high it goes, how long it stays up and how fast it lands, and draws the same launch at sea level, without spin and with no air at all, so that you can see what each effect is worth.

The idea

Without air a thrown ball feels only gravity, and its path is the parabola of every physics course. In air two more forces appear (Figure 1). Drag points straight back along the path and grows with the square of the speed: double the speed and the drag is four times as large. For a baseball at 100 mph the drag is about equal to the ball's weight, which is why real fly balls fall far short of the parabola. The spin force (the Magnus force) appears when the ball spins: the spinning surface drags air around with it, the wake behind the ball is thrown to one side, and the ball is pushed the other way, at right angles to its path and to its spin axis. Backspin pushes the ball up and keeps it in the air longer; topspin pushes it down; sidespin bends it left or right. That one force is the rise of a golf drive, the dip of a topspin forehand and the bend of a free kick.

A ball in flight with three force arrows: weight straight down, drag straight back along the path, and the spin force at right angles to the path
Figure 1: The three forces on a ball in flight

Both air forces are proportional to the density of the air. At 5,280 ft the standard atmosphere has about 85 percent of the density of sea level, so a fly ball meets 15 percent less drag and carries farther; it also gets 15 percent less lift from its backspin, which takes back part of the gain.

The equations

The ball is treated as a point with mass m. Let u be its velocity through the air (its velocity over the ground minus the wind), V the size of u, ρ the air density, d the diameter and A = π d2/4 the frontal area. Newton's second law for the ball is

m a = weight + drag + spin force

drag = ½ ρ V2 A CD, directed against u

spin force = ½ ρ V2 A CL, directed along (spin axis) × u

Drag coefficient CD. A number near 0.5 for a smooth ball at low speed and 0.2 to 0.3 for a stitched or dimpled ball at game speeds. The presets hold it constant. The "smooth sphere" choice computes it at every instant from the Reynolds number Re = ρ V d / μ (μ is the viscosity of air) with the correlation of Morrison (2013):

CD = 24/Re + 2.6 (Re/5) / [1 + (Re/5)1.52] + 0.411 (Re/263,000)−7.94 / [1 + (Re/263,000)−8] + 0.25 (Re/106) / [1 + Re/106]

This curve includes the "drag crisis" near Re = 300,000, where the drag of a smooth sphere drops to a quarter of its value in a narrow range of speed. Roughness (stitches, dimples, fuzz) moves that drop to lower speeds, which is the reason a dimpled golf ball outflies a smooth one, and the reason the curve must not be used for a rough ball.

Lift coefficient CL. NASA Glenn's Beginner's Guide to Aeronautics writes the lift of a spinning ball as the ideal value for a smooth ball times a measured coefficient, here called Cs:

L = Cs (4/3) (4 π2 b3 s ρ V)

with b the radius and s the spin in revolutions per second; NASA gives Cs = 0.15 for a baseball and about 0.25 for a soccer ball. Dividing by ½ ρ V2 A puts the same force in the usual form:

CL = (16/3) Cs S,   S = π d n / V

S is the spin ratio: the speed of the ball's surface (π d n, with n in revolutions per second) over its speed through the air. This law makes CL grow with S without end, while measured lift levels off, so the tool holds CL at or below a limit (0.4 unless you change it in Advanced mode; the limit is this tool's judgment, not a sourced constant).

Air density. The pressure p at the field's altitude comes from the U.S. Standard Atmosphere, 1976; the density is ρ = p / (R T) with R = 287.05 J/(kg·K) and T the absolute temperature (the standard one at that altitude, or the one you enter).

Terminal velocity. A falling object speeds up until drag equals weight, then falls steadily at

Vt = √(2 m g / (ρ A CD))

No air. Launched at speed V and angle θ from a height Δh above the landing level:

t = [V sin θ + √((V sin θ)2 + 2 g Δh)] / g,   carry = V cos θ × t,   peak = launch height + (V sin θ)2 / (2 g)

With air the equations have no solution in formulas, because the forces change with the speed all along the path. The tool advances position and velocity in steps of 0.002 s with the classical fourth-order Runge-Kutta method: four evaluations of the acceleration per step, combined so that the error of a step shrinks with the fifth power of the step. The instant of landing and the top of the flight are located inside their step by bisection. As a check, the tool also adds up the work done by the air along the path and compares it with the energy the ball has lost.

Axes and signs. Distance downrange is measured along the direction of launch; sideways distances are positive to the left as seen from behind the ball. Spin tilt: 0° is pure backspin, 90° sidespin that curves right, 180° topspin, −90° sidespin that curves left.

What it assumes

A point mass: the ball does not bounce, roll or deform. The spin rate and the spin axis stay fixed from launch to landing (real spin decays a little, by a few percent per second for most balls). The drag and spin-lift coefficients of a preset are single numbers, the same at every speed. The wind is steady and level, the same at every height. The air density is that of the field altitude for the whole flight, including a long drop. Gravity is the standard 9.80665 m/s2. The ground is level.

When it misleads

When the answer is compared with one measured hit. Coefficients of real balls change with speed, seam orientation, dimple pattern, wear and humidity; two baseballs from the same box differ by several percent in carry. Use the tool to see what each effect is worth and how the answer moves when you change an input, not to predict a particular ball to the foot.

When the spin ratio is large (a slow ball spinning fast): the straight-line lift law overstates the force, and the result then depends on the limit placed on CL.

For a knuckleball or any ball with little spin and raised seams: its erratic movement comes from the seams, not from the Magnus force, and is not modeled.

For a coin, a shuttlecock, a frisbee or a football: they are not spheres. The penny preset is a flat fall, face to the wind, which is the slowest way a coin can fall; a tumbling coin falls faster.

Above about Mach 0.3 (roughly 230 mph at sea level): the air begins to compress and the coefficients change. The tool flags it.

Golf, tennis and basketball presets use illustrative coefficients typed from memory and not checked against a source; the baseball and soccer values are the ones NASA Glenn publishes.

Common mistakes

  • Using the 45° rule in air. The farthest throw is at 45° only with no air and level ground. With drag the best angle is lower, about 35° for a batted baseball, and backspin lowers it further (about 20° for the golf preset).
  • Making drag proportional to speed. For a ball in air at any ordinary speed drag goes with the square of the speed. The linear law (Stokes drag) holds only for tiny, slow objects such as a mist droplet.
  • Dropping the ½, or using the surface area. Drag = ½ ρ V2 A CD, and A is the frontal area π d2/4, a circle, not the surface of the sphere (π d2), which is four times as large.
  • Mixing pounds of mass and pounds of force. In U.S. units ρ must be in slug/ft3 (0.002377 at sea level) and V in ft/s for the force to come out in pounds. 100 mph is 146.7 ft/s. A 5 oz ball weighs 0.3125 lb and has a mass of 0.3125 / 32.17 = 0.00971 slug.
  • Using speed over the ground when there is wind. Drag and spin force depend on the speed of the ball through the air. Into a 10 mph headwind a 100 mph ball feels 110 mph of air, and 21 percent more drag.
  • Thinking a heavier ball always falls faster, or never does. In a vacuum all objects fall together. In air the terminal velocity goes with the square root of weight over area: of two balls the same size, the heavier one falls faster.
  • Expecting the ball to land as fast as it left. True without air only. A fly ball that leaves the bat at 100 mph lands near 60 mph; most of its energy has gone into the air.
  • Pointing the spin force along the spin axis. It is at right angles to both the axis and the path. Backspin (axis level, across the path) lifts; sidespin (axis vertical) curves.
  • Entering rpm where revolutions per second are wanted. The spin ratio uses π d n with n in revolutions per second: 1,800 rpm is 30 per second.
  • Believing a penny from a skyscraper is deadly. The no-air formula √(2 g h) gives 193 mph from 1,250 ft, but the coin reaches its terminal velocity in the first few seconds and never comes close.

How it was checked

Baseball and soccer-ball numbers were read on NASA Glenn's pages (5 oz, 2.9 in, CD 0.3, lift coefficient 0.15; 1 lb, 0.75 ft, CD 0.25, lift coefficient about 0.25), as were the flat-plate drag coefficient 1.28 and NASA's closed-form results for a ball thrown straight up with drag, which the integration reproduces. The no-air formulas, the terminal velocity and the fall from rest with drag (v = Vt tanh(g t / Vt)) are reproduced to better than one part in a billion. Seventy-two flights, including every "Try this" case in both unit systems, agree with a separately written integration (a different method with error control) to one part in a million or better. None of this checks the coefficients themselves against a measured flight.




References

NASA Glenn Research Center (2021). "Drag on a Baseball." In Beginner's Guide to Aeronautics, National Aeronautics and Space Administration, Cleveland, OH.

NASA Glenn Research Center (2021). "Lift of a Baseball." In Beginner's Guide to Aeronautics, National Aeronautics and Space Administration, Cleveland, OH.

NASA Glenn Research Center (2021). "Drag on a Soccer Ball." In Beginner's Guide to Aeronautics, National Aeronautics and Space Administration, Cleveland, OH.

NASA Glenn Research Center (2021). "Lift of a Soccer Ball." In Beginner's Guide to Aeronautics, National Aeronautics and Space Administration, Cleveland, OH.

NASA Glenn Research Center (2021). "Flight Equations with Drag." In Beginner's Guide to Aeronautics, National Aeronautics and Space Administration, Cleveland, OH.

NASA Glenn Research Center (2021). "Shape Effects on Drag." In Beginner's Guide to Aeronautics, National Aeronautics and Space Administration, Cleveland, OH.

National Oceanic and Atmospheric Administration, National Aeronautics and Space Administration, and United States Air Force (1976). U.S. Standard Atmosphere, 1976. NOAA-S/T 76-1562, U.S. Government Printing Office, Washington, DC.

Morrison, F. A. (2016). Data Correlation for Drag Coefficient for Sphere. Department of Chemical Engineering, Michigan Technological University, Houghton, MI.

United States Code (2023). Title 31, Section 5112: Denominations, Specifications, and Design of Coins. Office of the Law Revision Counsel, U.S. House of Representatives, Washington, DC.


DISCLAIMER: The methods and calculation on aNOWysis.com are provided as means to educate the reader. There is no warranty, expessed or implied, as to the relevance or accuracy of the methods or calculations. All calculations should be checked by a qualified analyst for appropriateness and accuracy. We will not be held liable for any damages, injuries or deaths caused by using methods or calculations from this site.