Tools › Civil and Geotechnical › Surveying and Earthwork › Traverse Closure and COGO


Traverse Closure and COGO

Enter a starting point and the direction and distance of each course of a survey traverse; get the latitudes and departures, the misclosure and its precision ratio 1 : n, the compass-rule or transit-rule adjustment, the adjusted coordinates, bearings and lengths, the area by coordinates and a plot of the traverse to scale. Click a case under Try this to see one worked.

  • Closed loop or link traverse; directions as bearings (N 45°30'15" E), azimuths, or interior or deflection angles with the angular misclosure balanced

  • The first course worked out as formula, numbers, answer; every course tabulated before and after adjustment

  • Area by coordinates in acres or hectares; Advanced mode adds the transit rule, your own precision standard and the inverse between two points

Traverse Closure and COGO


Unit System: /

/

1. Starting Point and Type of Traverse





2. Courses, in the Order Walked



1
2
3
4
5
6

3. Adjustment and Standard



4. Inverse Between Two Points (optional)





×

Traverse Closure and COGO

Method: Latitudes and Departures, Misclosure, Compass and Transit Rules, Area by Coordinates, Common Mistakes

What the tool does

You enter where a survey traverse starts and, for each course, its direction and its horizontal distance. The tool computes how far each course goes north and east, shows how far the traverse misses its closing point and what precision that is, spreads the miss over the courses by the compass or the transit rule, and gives the adjusted coordinates, lengths, bearings and area with a plot to scale.

The idea

A traverse is a chain of straight lines (courses) measured one after another. Every course is the long side of a right triangle whose other two sides run north-south and east-west. The north-south side is the latitude of the course and the east-west side is its departure:

latitude = L cos(bearing angle)    departure = L sin(bearing angle)

Latitudes are plus to the north and minus to the south; departures are plus to the east and minus to the west. With the azimuth (the direction measured clockwise from north, 0° to 360°) in place of the bearing angle, the cosine and sine carry the signs by themselves, which is how the tool computes them.

Left: a course from A to B bearing north 35 degrees east, with its latitude drawn north-south and its departure drawn east-west. Right: a six-course closed traverse to scale with the misclosure drawn magnified

Left: one course and its two parts. Right: the tool's first Try this case, a six-course boundary from a U.S. Navy training manual, with the misclosure drawn 20 times too large so that it can be seen.

Walk a closed loop and you return to the start, so the latitudes must add up to zero and so must the departures. Run between two known points and the sums must equal the differences of their coordinates. Measurements are never perfect, so the sums miss by a little. That miss is the misclosure, and it is the one check a traverse gives on itself.

Directions: bearings, azimuths and angles

A bearing is written N or S, an angle from 0° to 90°, then E or W: N 45°30'15" E is 45°30'15" east of north. An azimuth is a single angle clockwise from north. The four quadrants convert as:

BearingAzimuthLatitudeDeparture
N β Eβ++
S β E180° − β−+
S β W180° + β−−
N β W360° − β+−

When angles were measured instead of directions, the direction of the first course is entered and every other direction follows from it. The angle in a row is the one at the station where that course begins.

Interior angle, loop run counterclockwise: azimuth = previous azimuth + 180° + angle
Interior angle, loop run clockwise: azimuth = previous azimuth + 180° − angle
Deflection angle: azimuth = previous azimuth + angle to the right, or − angle to the left

The angles check themselves before any distance is used. The interior angles of a figure with n sides add up to (n − 2) × 180°; the deflection angles to the right minus those to the left add up to 360°. The difference from the measured sum is the angular misclosure, and it is spread evenly: each angle is corrected by −(misclosure) / n. The tool then computes the directions from the balanced angles.

Linear misclosure and precision

eN = Σ latitudes − (Nclose − Nstart)    eE = Σ departures − (Eclose − Estart)

For a closed loop the bracketed terms are zero. The two errors are the sides of a small right triangle whose long side is the linear misclosure:

e = √(eN² + eE²)    precision = 1 : (total length / e)

A misclosure of 0.5 ft in 5,000 ft of traverse is 1 : 10,000. The U.S. Army Corps of Engineers manual EM 1110-1-1005 (Table 4-1) lists the minimum closure by class of survey: 1 : 2,500 for construction layout (fourth order), 1 : 5,000 for third order class II, 1 : 10,000 for third order class I, 1 : 20,000 and 1 : 50,000 for second order, 1 : 100,000 for first order. The Bureau of Land Management applies a double test to the public land surveys: the error in latitude and the error in departure must each stay within 1/4000 of the perimeter (Manual of Surveying Instructions, 2009, sections 3-50 and 3-215). The tool compares the single ratio with the standard you enter and does not apply the double test.

Adjustment

Compass (Bowditch) rule. Each course takes a share of the misclosure in proportion to its length, with the sign reversed:

correction to latitude = −eN × L / ΣL    correction to departure = −eE × L / ΣL

It treats the angles and the distances as equally good and is the usual rule for boundary and construction work.

Transit rule. Each latitude takes a share of eN in proportion to its own size, and each departure a share of eE in proportion to its own size:

correction to latitude = −eN × |latitude| / Σ|latitudes|    correction to departure = −eE × |departure| / Σ|departures|

It changes directions less and lengths more, so it suits work where the angles are trusted more than the distances. On a roughly square lot the two rules give nearly the same answer. On a long narrow strip they differ: the compass rule swings the long sides, the transit rule stretches or shortens the short ends (the last Try this case).

After either rule the corrected latitudes and departures close exactly. The coordinates of each station are those of the one before plus the adjusted latitude and departure; the adjusted length of a course is √(lat² + dep²) and its adjusted bearing angle is the angle whose tangent is |dep| / |lat|, with N or S from the sign of the latitude and E or W from the sign of the departure. Finding a length and direction from two sets of coordinates in this way is called an inverse.

Area by coordinates

For the stations of a closed figure taken in order and the last joined back to the first:

2A = Σ (Ni Ei+1 − Ni+1 Ei)    A = |2A| / 2

Written as a column of coordinates, each term is one product down to the right minus one product down to the left, which is why it is called the shoelace or cross-multiplication method. The sign of the sum only tells whether the figure was walked clockwise or counterclockwise. One acre is 43,560 square feet; one hectare is 10,000 square meters. The area is computed from the adjusted coordinates, as the Bureau of Land Management manual directs (section 2-23: the closing error is balanced by the compass rule before any area is calculated).

What it assumes

A flat (plane) survey: distances are horizontal and the north lines at every station are parallel. Courses are straight. The distances have already been corrected for slope, tape or instrument constants and, where a grid is used, for elevation and grid scale. Bearings and azimuths refer to one meridian. In angle entry the first direction is taken as exact and the angular misclosure is shared equally. The foot is the international foot of 0.3048 m exactly; the U.S. survey foot (1200/3937 m, deprecated in the United States from the end of 2022) is longer by 2 parts in a million, which matters only when feet are converted to meters or when large state plane coordinates are converted.

When it misleads

A good closure is not proof of a good survey. An error common to every distance (a tape that is too long, a wrong prism constant) scales the whole figure and closes perfectly, with the wrong area. Two mistakes can cancel. A link traverse checks the scale against the known points; a loop does not.

The rules spread error; they do not find it. If one distance was misread by 10 ft, both rules move every station to hide it. When the precision is far below the standard, look for the blunder: the bearing of the misclosure points along the course with the bad distance.

Over long distances the earth is not flat. Meridians converge, and state plane work needs the grid factor and the convergence angle. This tool applies neither.

A boundary that crosses itself gives an area that is the difference of its loops, not the land enclosed. The tool warns when the adjusted figure crosses.

Curved boundaries are not handled: the area is that of the straight-line figure. Arc segments must be added or subtracted separately; the Horizontal and Vertical Curves tool gives the elements of a circular curve.

The results are for learning and for checking hand computations. A boundary, plat or legal description must be prepared by a licensed surveyor.

Common mistakes

  • Sine and cosine swapped. Latitude goes with the cosine and departure with the sine, because the bearing angle is measured from the north-south line, not from the east-west axis used in mathematics.
  • Wrong signs. The letters of the bearing give the signs: N +, S − for the latitude; E +, W − for the departure. A course S 32°40' W has both negative.
  • Minutes and seconds treated as decimals. 45°30' is 45.5°, not 45.30°. Divide minutes by 60 and seconds by 3,600 before taking a sine or cosine.
  • Calculator in radians (or in grads) when the angles are in degrees.
  • Back bearing used for a course. The direction must be the one in which the course is walked; the opposite direction (N and S exchanged, E and W exchanged) reverses both signs.
  • Correction applied with the sign of the error. The correction is the error with its sign reversed: a plus misclosure in latitude means every latitude correction is minus.
  • Slope distance used as horizontal. Reduce it first: horizontal = slope × cos(vertical angle).
  • Adjusting before the angles are balanced, or computing the area from unadjusted coordinates of a figure that does not close.
  • Forgetting the closing term in the area. The last station must be multiplied back against the first, and the total halved.
  • Interior angle taken for the wrong direction of travel. The same angle is added when the loop runs counterclockwise and subtracted when it runs clockwise; the wrong choice gives a mirror image of the lot (same area, wrong bearings).
  • Mixing survey feet and international feet when converting coordinates to meters: 2 parts per million is 4 ft on a coordinate of 2,000,000 ft.

Sources and what was checked

The first Try this case is the closed traverse of NAVEDTRA 14337, Engineering Aid 2, Figures 7-12 to 7-14 (pages 7-10 and 7-11); the second is the straight-line boundary of its Figure 7-32 (page 7-22); the fourth is the compass-rule form of USACE EM 1110-1-1005, Figure 3-11 (page 3-21). The tool reproduces their printed latitudes, departures, corrections and areas within the rounding of the print. The manuals worked with five-place tables and rounded each product to 0.01 ft, so their closure figures (0.33 and 2.24 ft, 1 : 1157; 0.036 ft, 1 : 16,726) differ slightly from the exact arithmetic shown here (0.321 and 2.264 ft, 1 : 1,143; 0.041 ft, 1 : 14,550). Figure 3-11 prints two azimuths as 188°03'48" and 288°03'14"; its own angles, latitudes and departures give 188°08'48" and 283°03'14", which the tool uses. The link traverse and the long narrow strip are original, illustrative cases checked against an independent computation.




References

Naval Education and Training Professional Development and Technology Center (1994). Engineering Aid 2. Nonresident Training Course NAVEDTRA 14337, U.S. Navy, Pensacola, FL.

U.S. Army Corps of Engineers (2007). Control and Topographic Surveying. Engineer Manual EM 1110-1-1005, Department of the Army, Washington, DC.

Bureau of Land Management (2009). Manual of Surveying Instructions: For the Survey of the Public Lands of the United States. U.S. Department of the Interior, Government Printing Office, Denver, CO.

Federal Geodetic Control Committee (1984). Standards and Specifications for Geodetic Control Networks. National Geodetic Survey, National Oceanic and Atmospheric Administration, Rockville, MD.

National Institute of Standards and Technology and National Oceanic and Atmospheric Administration (2020). "Deprecation of the United States (U.S.) Survey Foot." Federal Register, Vol. 85, pp. 62698–62708.


DISCLAIMER: The methods and calculation on aNOWysis.com are provided as means to educate the reader. There is no warranty, expessed or implied, as to the relevance or accuracy of the methods or calculations. All calculations should be checked by a qualified analyst for appropriateness and accuracy. We will not be held liable for any damages, injuries or deaths caused by using methods or calculations from this site.