Leidel, N. A., Busch, K. A., and Lynch, J. R. (1977). Occupational Exposure Sampling Strategy Manual. DHEW (NIOSH) Publication No. 77-173, National Institute for Occupational Safety and Health, Cincinnati, OH.
U.S. Environmental Protection Agency (2009). Statistical Analysis of Groundwater Monitoring Data at RCRA Facilities: Unified Guidance. EPA 530/R-09-007, Office of Resource Conservation and Recovery, Washington, DC.
Singh, A., and Singh, A. K. (2015). ProUCL Version 5.1 Technical Guide: Statistical Software for Environmental Applications for Data Sets with and without Nondetect Observations. EPA/600/R-07/041, U.S. Environmental Protection Agency, Washington, DC.
U.S. Environmental Protection Agency (1992). Supplemental Guidance to RAGS: Calculating the Concentration Term. Publication 9285.7-081, Office of Solid Waste and Emergency Response, Washington, DC.
Land, C. E. (1971). "Confidence Intervals for Linear Functions of the Normal Mean and Variance." The Annals of Mathematical Statistics, Vol. 42, No. 4, pp. 1187–1205.
Land, C. E. (1975). "Tables of Confidence Limits for Linear Functions of the Normal Mean and Variance." In Selected Tables in Mathematical Statistics, Vol. III, American Mathematical Society, Providence, RI, pp. 385–419.
Finney, D. J. (1941). "On the Distribution of a Variate Whose Logarithm Is Normally Distributed." Supplement to the Journal of the Royal Statistical Society, Vol. 7, No. 2, pp. 155–161.
Odeh, R. E., and Owen, D. B. (1980). Tables for Normal Tolerance Limits, Sampling Plans, and Screening. Marcel Dekker, New York.
Helsel, D. R., and Cohn, T. A. (1988). "Estimation of Descriptive Statistics for Multiply Censored Water Quality Data." Water Resources Research, Vol. 24, No. 12, pp. 1997–2004.
Royston, P. (1995). "Remark AS R94: A Remark on Algorithm AS 181: The W-test for Normality." Journal of the Royal Statistical Society, Series C (Applied Statistics), Vol. 44, No. 4, pp. 547–551.
Jahn, S. D., Bullock, W. H., and Ignacio, J. S. (eds.) (2015). A Strategy for Assessing and Managing Occupational Exposures, 4th ed. American Industrial Hygiene Association, Falls Church, VA.
Worked Examples
Published examples this tool reproduces; each page lists the inputs to enter and the printed answers.
DISCLAIMER: The methods and calculation on aNOWysis.com are provided as means to educate the reader. There is no warranty, expessed or implied, as to the relevance or accuracy of the methods or calculations. All calculations should be checked by a qualified analyst for appropriateness and accuracy. We will not be held liable for any damages, injuries or deaths caused by using methods or calculations from this site.
Terms of Service & Liability Disclaimer
Please read and accept these terms for the best experience with our analysis tools.
⚠️ Important Legal Notice
BY USING THESE ANALYSIS TOOLS, YOU ACKNOWLEDGE AND AGREE THAT:
NO WARRANTY: These tools are provided "AS IS" and may contain errors, bugs, or inaccuracies
EDUCATIONAL USE ONLY: Results are for preliminary analysis and educational purposes only
NOT PROFESSIONAL ADVICE: These tools do not replace professional engineering judgment
VERIFICATION REQUIRED: All results must be independently verified by a licensed professional engineer
POTENTIAL RISKS: Incorrect results could lead to catastrophic failures causing property damage, injury, or death
Limitation of Liability
UNDER NO CIRCUMSTANCES SHALL AVERY AEROSPACE CORPORATION, ITS DIRECTORS, EMPLOYEES, OR AFFILIATES BE HELD LIABLE FOR:
Any direct, indirect, incidental, consequential, special, punitive, or exemplary damages
Property damage, personal injury, or death resulting from use of these tools
Errors, inaccuracies, or incorrect calculations produced by the tools
Design failures, structural collapses, or system malfunctions based on tool outputs
Any damages whatsoever, even if we have been advised of the possibility of such damages
Your Responsibilities
You agree to:
Use at Your Own Risk: You assume all risks associated with using these analysis tools
Professional Verification: Engage licensed professional engineers for all critical design work
Independent Judgment: Exercise independent engineering judgment and not rely solely on tool outputs
Code Compliance: Ensure all designs comply with applicable codes, standards, and regulations
Indemnification: Defend and hold harmless the Company from any claims arising from your use of these tools
Acceptance
By clicking "I Accept and Agree" below, you acknowledge that you have read, understood, and agree to be bound by: