Tools › Structures › Frames and Trusses › Ring Frame Analysis › Example

Floating frame standing 1 in off the skin: ring radius, shear flow at the skin line, shear clips and doublers under floor loads

ToolRing Frame Analysis
SourceIllustrative case. Loads of Niles, A. S., and Newell, J. S. (1943). Airplane Structures, 3rd ed., Vol. I. John Wiley and Sons, New York. Art. 17:8; shear flow at a radius different from the frame's neutral fiber as in Fahlbusch, H., and Wegner, W. (1941). Stress Analysis of Circular Frames. NACA Technical Memorandum 999, eq. (1) to (12).
LevelProfessional

Problem

A floating frame stands 1 in inside a skin of 42 in inner radius: the stringers pass through the gap and the frame is tied to the skin only by shear clips. Its centroid is 2 in inside its own outer cap. It carries the four floor and seat loads of Niles and Newell's example (1,020, 1,440, 935 and 675 lb down at x = −28.5, −0.5, 21.5 and 29.25 in), entered as added limit loads. Find the ring radius and the added internal loads with the skin shear flow acting where the skin is, 3 in outboard of the frame's centroid, and check the default doublers and shear clips spaced 4 in with two fasteners each.

Inputs to Enter

  • Advanced mode; Skin Inner Radius 42 in; Frame Attachment: floating (shear clips); Gap to Inner Skin 1.0 in; Frame Area 0.60 in², Frame Inertia 2.0 in⁴, Centroid to Outer Frame 2 in, Frame Modulus 10.5 Msi, Skin Thickness 0.040 in
  • Frame Depth 4.5 in, Outer Cap Thickness 0.050 in, Inner Cap Thickness 0.050 in; Shear Flow Acts: on the skin line (correction)
  • Default loads B, C, D, E by x on the lower half; reinforcement: additional load, limit loads, default doublers inside the C over the whole ring
  • Frame to Skin Attachment: Pitch or Clip Spacing 4 in, allowable computed, Fasteners per Clip 2
Open the Ring Frame Analysis tool

Answers

  • Ring radius R = R_s − g_sk − y_f = 42 − 1 − 2 = 39 in (40 in for the same frame shear-tied); effective skin is not available for a floating frame; the same x positions now fall at 223.05°, 269.27°, …
  • Skin shear flow at the skin mid-thickness, radius 42.02 in, 3.02 in outboard of the ring axis; it peaks at 31.74 lb/in
  • At the section at 0°: M = −11,084 lb-in, N = +1,097.4 lb, S = +193.73 lb, of which 103.27 lb is the skin-line correction; the correction adds no bending moment
  • Largest moment 14,790 lb-in at 269.27° (15,463 lb-in shear-tied), largest normal force 1,755.9 lb and shear −899.71 lb at 318.59°; diameter changes +0.5013 and −0.5018 in
  • Doublers stay on the frame's caps: y_o = 0.050 + 0.125/2 = 0.1125 in, y_i = 4.5 − 0.050 − 0.125/2 = 4.388 in, arm 4.275 in
  • Margins: outer cap tension 64.00/35.41 − 1 = +0.81; inner cap compression 39.00/24.59 − 1 = +0.59; web shear buckling 9.971/6.314 − 1 = +0.58 (lowest); cap fastener 595.7/236.8 − 1 = +1.52
  • Shear clips: 31.74 lb/in × 4 in × 1.5 = 190.4 lb per clip against 2 × 595.7 = 1,191 lb, margin +5.26

Notes

Enter the inputs above and press Submit; the values are asserted by test_ring_frame_analysis_page.php. The skin-line correction with the shear flow at one radius and the ring at another reproduces NACA TM 999 in the library test. A floating frame receives the skin shear at its clips, not continuously; the tool keeps the continuous shear flow of the book for the internal loads and uses the clip spacing only for the clip check. The loads are the book's; the frame, gap, doublers and clips are invented for illustration, and the margins say nothing about the existing frame under its own baseline loads.

More Examples for This Tool