AISI 301and Relateda,b,c-Annealed Sheet and strip: MIL-HDBK-5J Design Allowables
show SI units (MPa, GPa, kg/m³) open the MIL-HDBK-5J tool compare against temperature find alternatives
| Material class | Steel |
| Alloy / temper / form | AISI 301and Relateda,b,c / Annealed / Sheet and strip |
| Specifications | AMS 5901 |
| Handbook | MIL-HDBK-5J, 31 January 2003, section 2.7.1.0, Table 2.7.1.0(b) (pdf page 223 of the chapter file) |
| Dimension bands | 1 |
| Density | 0.286 lb/in3 |
Design Mechanical and Physical Properties (room temperature)
As printed in the handbook table. Bases: A and B are statistical minimums (99 % and 90 % probability at 95 % confidence), S the specification minimum. Grain directions: L longitudinal, LT long transverse, ST short transverse.
| Dimension band | 0.000–0.187 in | |
|---|---|---|
| Specification | AMS 5901 | |
| Basis | S | |
| Ftu, ksi | L | 73 |
| LT | 75 | |
| Fty, ksi | L | 26 |
| LT | 30 | |
| Fcy, ksi | L | 23 |
| LT | 29 | |
| Fsu, ksi | L | 50 |
| LT | 50 | |
| Fbru (e/D = 2.0), ksi | L | 162 |
| LT | 162 | |
| Fbry (e/D = 2.0), ksi | L | 55 |
| LT | 55 | |
| e, % | L | … |
| LT | 40 | |
| E, Msi | 29 | |
| G, Msi | 11.2 | |
| ν | 0.27 | |
| ρ, lb/in3 | 0.286 | |
Effect of Temperature
Percent of the room-temperature value against temperature, digitized from the handbook figures (the shortest exposure of each figure, every 10 °F). Strength curves give the allowable at temperature; "after exposure" curves give the room-temperature property after a soak at that temperature.
Strength allowables at temperature, percent of room temperature
| °F | F_tu | F_ty |
|---|---|---|
| -300 | 200.4 | 126.3 |
| -200 | 173.1 | 121.3 |
| -100 | 145.6 | 114.8 |
| 0 | 118.9 | 106.5 |
| 100 | 95.6 | 96.8 |
| 200 | 81.1 | 85.3 |
| 300 | 73.5 | 74.5 |
| 400 | 70.3 | 67.2 |
| 500 | 69.4 | 62.8 |
| 600 | 69 | 61.3 |
| 700 | 68.5 | 61 |
| 800 | 68.3 | 61 |
| 1000 | 63.3 | 59.8 |
| 1200 | 52.3 | 53.9 |
Factors in percent of the room-temperature allowable.
Other AISI 301and Relateda,b,c Tables
- AISI 301and Relateda,b,c-� Hard Sheet and strip (Table 2.7.1.0(b))
- AISI 301and Relateda,b,c-� Hard Sheet and strip (Table 2.7.1.0(b))
- AISI 301and Relateda,b,c-� Hard Sheet and strip (Table 2.7.1.0(b))
- AISI 301and Relateda,b,c-Full Hard Sheet and strip (Table 2.7.1.0(b))
Source and Use
U.S. Department of Defense (2003). Metallic Materials and Elements for Aerospace Vehicle Structures. MIL-HDBK-5J, 31 January 2003 (public domain). The values are the handbook's design allowables as extracted from the chapter tables; check the printed table before use in a certified analysis, and note that MIL-HDBK-5J was superseded by MMPDS, whose later editions may differ. No warranty is given.