7075-T62 Plate: MIL-HDBK-5J Design Allowables

show US units (ksi, Msi, lb/in³) open the MIL-HDBK-5J tool compare against temperature find alternatives

Design Mechanical and Physical Properties (room temperature)

Converted from the handbook table (ksi, Msi, lb/in³) and rounded to 4 significant figures; dimension bands in inches with mm in parentheses. Bases: A and B are statistical minimums (99 % and 90 % probability at 95 % confidence), S the specification minimum. Grain directions: L longitudinal, LT long transverse, ST short transverse.

Effect of Temperature

Percent of the room-temperature value against temperature, digitized from the handbook figures (the shortest exposure of each figure, every 10 °F). Strength curves give the allowable at temperature; "after exposure" curves give the room-temperature property after a soak at that temperature.

Moduli at temperature

Other 7075 Tables

• 7075-T6 Clad sheet (Table 3.7.6.0(c))
• 7075-T6 Die forging (Table 3.7.6.0(e))
• 7075-T6 Hand forging (Table 3.7.6.0(f))
• 7075-T6 and T62 Clad sheet (Table 3.7.6.0(c))
• 7075-T6 and T62 Sheet (Table 3.7.6.0(b))
• 7075-T6, T651, and T62 Bar, rod, and shapes: rolled, drawn, or cold-finished (Table 3.7.6.0(d))
• 7075-T6, T6510, T6511, and T62 Extrusion (rod, bar, and shapes) (Table 3.7.6.0(g))
• 7075-T62 Clad plate (Table 3.7.6.0(c))
• 7075-T651 Clad plate (Table 3.7.6.0(c))
• 7075-T651 Plate (Table 3.7.6.0(b))
• 7075-T652 Die forging (Table 3.7.6.0(e))
• 7075-T652 Hand forging (Table 3.7.6.0(f))
• 7075-T73 Hand forging (Table 3.7.6.0(f))
• 7075-T73 Sheet (Table 3.7.6.0(b))
• 7075-T7351 Plate (Table 3.7.6.0(b))
• 7075-T7352 Die forging (Table 3.7.6.0(e))
• 7075-T7352 Hand forging (Table 3.7.6.0(f))
• 7075-T73a, T73510, T73511 Extrusion (rod, bars, and shapes) (Table 3.7.6.0(g))
• 7075-T73a,b Die forging (Table 3.7.6.0(e))
• 7075-T73b or T7351 Bar, rod, and shapes: rolled, drawn, or cold-finished (Table 3.7.6.0(d))
• 7075-T76 Clad sheet (Table 3.7.6.0(c))
• 7075-T76 Sheet and plate (Table 3.7.6.0(b))
• 7075-T76, T76510, T76511 Extrusion (rod, bar, and shapes) (Table 3.7.6.0(g))
• 7075-T7651 Clad plate (Table 3.7.6.0(c))
• 7075-T7651 Sheet and plate (Table 3.7.6.0(b))

Source and Use

U.S. Department of Defense (2003). Metallic Materials and Elements for Aerospace Vehicle Structures. MIL-HDBK-5J, 31 January 2003 (public domain). The values are the handbook's design allowables as extracted from the chapter tables; check the printed table before use in a certified analysis, and note that MIL-HDBK-5J was superseded by MMPDS, whose later editions may differ. No warranty is given.