Inconel 718-Solution treated and aged per indicated specificat Tubing: MIL-HDBK-5J Design Allowables
show SI units (MPa, GPa, kg/m³) open the MIL-HDBK-5J tool compare against temperature find alternatives
| Material class | Heat-Resistant |
| Alloy / temper / form | Inconel 718 / Solution treated and aged per indicated specificat / Tubing |
| Specifications | AMS 5589; AMS 5590 |
| Handbook | MIL-HDBK-5J, 31 January 2003, section 6.3.5.0, Table 6.3.5.0(b) (pdf page 52 of the chapter file) |
| Dimension bands | 2 |
| Density | 0.297 lb/in3 |
Design Mechanical and Physical Properties (room temperature)
As printed in the handbook table. Bases: A and B are statistical minimums (99 % and 90 % probability at 95 % confidence), S the specification minimum. Grain directions: L longitudinal, LT long transverse, ST short transverse.
| Dimension band | 0.010–1.000 in | 0.010–1.000 in | |
|---|---|---|---|
| Specification | AMS 5589 | AMS 5590 | |
| Basis | S | S | |
| Ftu, ksi | L | 185 | 170 |
| Fty, ksi | L | 150 | 145 |
| e, % | L | 12 | 15 |
| E, Msi | 29.4 | 29.4 | |
| Ec, Msi | 30.9 | 30.9 | |
| G, Msi | 11.4 | 11.4 | |
| ν | 0.29 | 0.29 | |
| ρ, lb/in3 | 0.297 | 0.297 | |
Effect of Temperature
Percent of the room-temperature value against temperature, digitized from the handbook figures (the shortest exposure of each figure, every 10 °F). Strength curves give the allowable at temperature; "after exposure" curves give the room-temperature property after a soak at that temperature.
Strength allowables at temperature, percent of room temperature
Moduli at temperature
| °F | F_tu | F_ty |
|---|---|---|
| -300 | 115.8 | 115.8 |
| -200 | 111.1 | 111.1 |
| -100 | 106.6 | 106.6 |
| 0 | 102.5 | 102.5 |
| 100 | 99.8 | 99.8 |
| 200 | 97.2 | 97.2 |
| 300 | 95.9 | 95.9 |
| 400 | 94.5 | 94.5 |
| 500 | 93.8 | 93.8 |
| 600 | 92.8 | 92.8 |
| 700 | 92.1 | 92.1 |
| 800 | 91.2 | 91.2 |
| 1000 | 89.3 | 89.3 |
| 1200 | 80.6 | 80.6 |
Factors in percent of the room-temperature allowable.
Other Inconel 718 Tables
- Inconel 718-Solution treated and aged per indicated specificat Bar (Table 6.3.5.0(c))
- Inconel 718-Solution treated and aged per indicated specificat Forging (Table 6.3.5.0(c))
- Inconel 718-Solution treated and aged per indicated specificat Plate (Table 6.3.5.0(b))
- Inconel 718-Solution treated and aged per indicated specificat Sheet (Table 6.3.5.0(b))
- Inconel 718-Solution treated and aged per indicated specificat Sheet and plate (Table 6.3.5.0(b))
Source and Use
U.S. Department of Defense (2003). Metallic Materials and Elements for Aerospace Vehicle Structures. MIL-HDBK-5J, 31 January 2003 (public domain). The values are the handbook's design allowables as extracted from the chapter tables; check the printed table before use in a certified analysis, and note that MIL-HDBK-5J was superseded by MMPDS, whose later editions may differ. No warranty is given.