Inconel 600-Hot-worked Square, / hexagon, and / rectangle: MIL-HDBK-5J Design Allowables
show SI units (MPa, GPa, kg/m³) open the MIL-HDBK-5J tool compare against temperature find alternatives
| Material class | Heat-Resistant |
| Alloy / temper / form | Inconel 600 / Hot-worked / Square, / hexagon, and / rectangle |
| Specifications | ASTM B166 |
| Handbook | MIL-HDBK-5J, 31 January 2003, section 6.3.2.0, Table 6.3.2.0(d) (pdf page 30 of the chapter file) |
| Dimension bands | 1 |
| Density | 0.304 lb/in3 |
Design Mechanical and Physical Properties (room temperature)
As printed in the handbook table. Bases: A and B are statistical minimums (99 % and 90 % probability at 95 % confidence), S the specification minimum. Grain directions: L longitudinal, LT long transverse, ST short transverse.
| Dimension band | all | |
|---|---|---|
| Specification | ASTM B166 | |
| Basis | S | |
| Ftu, ksi | L | 85 |
| Fty, ksi | L | 35 |
| e, % | L | 30 |
| E, Msi | 30 | |
| Ec, Msi | 30 | |
| G, Msi | 11 | |
| ν | 0.29 | |
| ρ, lb/in3 | 0.304 | |
Effect of Temperature
Percent of the room-temperature value against temperature, digitized from the handbook figures (the shortest exposure of each figure, every 10 °F). Strength curves give the allowable at temperature; "after exposure" curves give the room-temperature property after a soak at that temperature.
Strength allowables at temperature, percent of room temperature
Moduli at temperature
| °F | F_tu | F_ty | F_cy | F_su | F_bru |
|---|---|---|---|---|---|
| 100 | 99 | 99 | 98.4 | 98.4 | 99.1 |
| 200 | 97 | 97 | 94 | 98.3 | 98.6 |
| 300 | 94.1 | 94.1 | 90.4 | 97.6 | 98.1 |
| 400 | 91.4 | 91.4 | 89.7 | 97 | 97.5 |
| 500 | 89.6 | 87.9 | 89.1 | 96.2 | 96.6 |
| 600 | 85.9 | 85.9 | 87.5 | 95.7 | 95.9 |
| 700 | 84.6 | 82 | 84.9 | 95.1 | 94.8 |
| 800 | 82 | 79.3 | 81.7 | 93.5 | 94.3 |
| 1000 | 77.1 | 73.2 | 86.5 | 88.9 | |
| 1200 | 65.4 | 65.4 | 75.5 | 70.8 |
Factors in percent of the room-temperature allowable.
Other Inconel 600 Tables
- Inconel 600-Annealed Bar and rod (Table 6.3.2.0(d))
- Inconel 600-Annealed Forging (Table 6.3.2.0(b))
- Inconel 600-Annealed Sheet, strip, and plate (Table 6.3.2.0(b))
- Inconel 600-Cold drawn Tubing (Table 6.3.2.0(b))
- Inconel 600-Cold-worked Round (Table 6.3.2.0(c))
- Inconel 600-Cold-worked Square, hexagon, and rectangle (Table 6.3.2.0(c))
- Inconel 600-Hot-worked Round (Table 6.3.2.0(d))
Source and Use
U.S. Department of Defense (2003). Metallic Materials and Elements for Aerospace Vehicle Structures. MIL-HDBK-5J, 31 January 2003 (public domain). The values are the handbook's design allowables as extracted from the chapter tables; check the printed table before use in a certified analysis, and note that MIL-HDBK-5J was superseded by MMPDS, whose later editions may differ. No warranty is given.